Custom Steel and Aluminum Fabrications

Clegg Industries builds custom steel and aluminum fabrication in our own shop in Victoria, TX. We make the parts, frames, carts, and stands that don’t come out of a catalog.

We have built for every branch of the U.S. military, federal agencies, defense contractors, and NASA’s space shuttle program since 1979. When you call us, a person picks up.

Start Your Fabrication Project Call (361) 578-0291

What We Fabricate

Aerospace and Radar Support Equipment

Carts, frames, and fixtures for moving and building large radar parts.

Test Stands

Stands and rigs for testing gear to military specs.

Power Skids

Skid-mounted generators with their own fuel tanks for remote sites.

Vehicle and Trailer Parts

Partitions, steps, rails, seats, racks, and brackets for vehicles and trailers.

Architectural Pieces

Large one-off pieces built to match old blueprints.

Custom Parts and Components

Small parts made to fit, from patch panels to machined adapters.

Custom Fabrication Projects

Projects №499 and №500, Radar Antenna Carts

We built two all-aluminum carts that move parts of an AEW radar antenna between the plane, the trailer, and the service shop.

Heavy-duty aluminum with custom lathed parts
Locking pin system and a thick rubber protective layer
Industrial yellow coating on the low rise cart

Project №245, Radome Assembly Frame

We built an aluminum frame that holds the dome and electronics while a radome is put together.

Moves on three axes using linear slide bearings
Ball screw assemblies for fine, step-by-step movement
Handrails and protective covers

Project №281, Watertight Test Stand

All-aluminum stand built to meet military specs
Lightweight and modular for fast setup and teardown

Project №240, Skid-Mounted Generator

Built on an ISO standard skid
Custom fuel tank, fuel transfer system, and storage locker
Powers a mobile parts shop at remote sites

Project №452, Church Steeple

7 feet 2 inches wide and 24 feet tall
Octagon-shaped aluminum frame covered in copper sheeting
Built from the church’s original blueprints to replace a steeple lost to a hurricane
Original cross repaired and put back on top
Built and installed by Clegg

Snow Melters for Antarctic Field Camps

Two stainless steel snow melters that feed filtered water into 100-gallon tanks in each module

Aluminum Vehicle Partition

All-aluminum partition with a gloss black finish and 1/2-inch Lexan windows

Parts We Make Often

Aluminum stairs, including stairs with electric actuators
Vehicle steps and safety rails
Aluminum bench seating
Cylinder and bottle racks
Mounting brackets for trailer equipment
Helicopter rotor supports for transport trailers
Patch panels
Machined aluminum adapters

See Custom Design and Fabrication

Inside Our Shop

Our shop is 20,000 square feet. It is set up to cut, bend, weld, and finish metal under one roof.

10-foot CNC press brake and 10-foot CNC shear
Steel and aluminum cut line, with aluminum stocked on site
TIG, MIG, and stick welding stations
Hydraulic finger brake and plate roller
65-foot paint booth and sandblasting stations
5-ton and 2-ton overhead cranes

Two Ways to Start

Send us your drawings or specs and we will build to them.

Or tell us the problem and we will design the part with you.

Parts for Your Vehicle, Trailer, or Structure

A lot of our fabrication goes into our own vehicles, trailers, and structures. The same crew can build parts for yours.

Specialty Vehicles Specialty Trailers Specialty Structures All Specialty Vehicles and Enclosures

Credentials

ICD 705

ISO 9000

CMMC Level 1

DDTC registered

ITAR and EAR compliant

Woman-Owned Small Business

ASME and AWS welders

TEMPEST and STC tested by third parties

Our quality program is written down. You can review it as part of your buying process.

What to Have Ready When You Call

What does the part need to do?
Do you have drawings, specs, or a sample to match?
What material and finish do you need?
How many do you need?
Does it have to meet a military or industry spec?
When do you need it?

Don’t have every answer? Call anyway. We will help you sort out what matters for your project.

Frequently Asked Questions

What metals do you work with?

We work in steel, aluminum, and stainless steel.

Can you build to military specs?

Yes. Our watertight test stand was built to meet military specs.

Do you machine parts?

Yes. We have made custom lathed aluminum parts and a machined hex plate adapter.

Do you paint and finish parts?

Yes. We sandblast, paint, and coat in house, with a 65-foot paint booth.

Start Your Custom Fabrication Project

Call (361) 578-0291 or email sales@cleggind.com. Send drawings if you have them. A person will answer and help you plan it.

Start Your Fabrication Project